gear pair

Nonlinear Dynamics Research of Transmission Gear Pair with Random Assembly Gap

考虑随机装配间隙的变速器齿轮副非线性动力学研究

Study on Relative Sliding Ratio of Involute Internal Gear Pair

渐开线内齿轮副相对滑动率的研究

Some applied experiences on domestication field of high speed gear pair with special structure for large scale refrigerator are recommended.

介绍了一种结构特殊的大型冷冻机高速齿轮副国产化方面的一些实用经验。

In accordance with different combination forms of gear pair, the sliding ratio of crossed helical involute gear pair was calculated by using the formula, which was deduced for spot contact tooth surfaces and the sliding curve of the gear pair was drawn as well.

推导出点接触齿轮副齿面滑动系数的计算公式，并分别针对齿轮副的不同组合形式，计算交错轴渐开线斜齿圆柱齿轮传动的滑动系数，绘制该齿轮副的滑动曲线。

This paper discusses computing backlash of the gear pair and output mechanism of shaft of pin kind according to the requirement of tolerance of designing and manufacturing and the probable maximum and minimum values of backlash are precomputed, using probabilistic method.

文中叙述齿轮副的回差计算和销轴输出机构的回差计算，是根据设计制造的公差要求，按概率统计的方法预算出可能出现的最大与最小的回差值。

Stress Analysis for Cylindrical Helical Gear Pair in the Megawatt Level Wind-driven Generator

兆瓦级风力发电机增速器齿轮传动受力分析

Theoretical and Experimental Investigations of Torsional Vibration in a Helical Gear Pair with Backlash

含间隙的斜齿轮副扭振分析与试验研究

Newton Method for Determining the Addendum Modification Coefficient of Internal Gear Pair with Small Difference in Number of Teeth

确定少齿差内齿轮副变位系数的切线法一个比Newton法收敛快而稳的两点切线法

The Rave Engage Coefficient Value of Change Weekly Link Gear Pair

变周节齿轮副的啮合系数初探

3D engagement analysis on gear pair of transmission system of turbine starter

涡轮起动机传动系统的齿轮副三维啮合分析

study on the dynamic performance of a spur gear pair by linearization method

用线性化方法研究直齿圆柱齿轮的动态性能

Study of Involute Spur Gear Pair with Modified Factor' Limit Value

渐开线斜齿圆柱齿轮变位系数极值研究

Involute internal gear pair with small teeth difference

渐开线少齿差内齿轮副

It is put forward that experience formula to determine hardness relation between big wheel and little wheel of gear pair hardened tooth flank.

据此提出确定硬齿面齿轮副的大小齿轮之间硬度关系的经验公式。

Numerical Simulation and Power Flow Analyse on a Meshing Gear Pair with Backlash Nonlinearity

齿轮非线性系统的数值仿真与功率流分析

The minimum gear pair backlash design based on the moving characteristics of driving gear pair

基于换向传动齿轮副运动特点的最小齿轮副侧隙设计

Because of the meshing stiffness of a gear pair, the governing equation denotes a linear dynamic system with periodic time-varying coefficient.

由于齿轮副啮合刚度的影响，动力学方程式代表了一个具有时变系数的线性动力系统。

Relationships Between the Machinery Efficiency of the High-Speed Gear Pair and the Speed of the Driving Gear

高速齿轮副机械效率与主动轮转速的关系

Common Profile Equation of the Annulus in Sliding& Teeth. Gear Pair and Its Analysis of Clearance

活齿齿轮副内齿轮齿形通用方程式及间隙分析

Moreover, a gear pair with curvilinear-tooth traces operates without axial thrust force.

除此之外, 具有曲线型齿线之齿轮在运转时亦不会产生轴向的推力.

The relative sliding ratio formulas of an involute spur gear pair are developed The influences of relative sliding ratio on the gear wear, friction moment of engagement and elastohydrodynamic lubrication are analyzed

推导了渐开线圆柱齿轮副相对滑动率的计算公式，分析了相对滑动率对齿轮磨损、相啮合的摩擦力矩与弹流润滑等问题的影响

The relative sliding ratio formulas of an involute internal spur gear pair are developed.

推导了渐开线内齿轮副相对滑动率的计算公式。

The design of cylindrical worm gear pair with controllable spot engagement

可控点啮合圆柱蜗杆副的设计

Design of Shrinkage Tooth with Equal Tip Clearance of Hypoid Bevel Gear Pair with Half Generating Method

半展成法收缩齿等顶隙准双曲面锥齿轮副设计

Fuzzy three stage design method of hypoid gear pair

准双曲面齿轮的三次模糊设计法

Study on the Dynamic Response of the Gear Pair with Error Excitation

具有误差激励齿轮副的动态响应研究

A systemic analysis has been made for meshing properties of the straight conjugating internal gear pair in this paper, involving the solution of conjugated tooth profile, meshing process and line of action, as well as the influences of gear designing parameters on the contact ratio.

对直线共轭内啮合齿轮副的啮合特性进行了全面分析，包括共轭齿形的求解、啮合过程分析和重合度计算及齿轮参数对重合度的影响等内容。

The design of involute planetary gear pair with a slightly different tooth number of zero restraint is introduced.

文中还介绍了零约束渐开线少齿差行星齿轮传动的机构设计。

Selection of the Design Parameters on Planetary Transmission Using Internal Involute Gear Pair with Small Tooth Difference

渐开线少齿差传动设计参数的选择

When worm gear pair is formed by standard worm and worm wheel generated by hob of type ⅱ, its sensibility to errors is reduced while the worm gear pair is assembled originally and good tooth contact quality is acquired after its running in.

本文提出失配修形法，用标准蜗杆与由Ⅱ型滚刀加工的蜗轮失配啮合，使蜗杆副初装时对误差不敏感，跑合后得到良好的接触质量。